This Deluxe Snow Thrower Cab Installation guide is an important article to read if you have this working tool. There are still people who seek help from technician and pay just to get the snow thrower cab installed. But why pay if you can get this done yourself?

CHECKOUT THIS POST >>> How to Change the Air Filter on a Riding Mower
Read more on this article to learn the installation process of the Deluxe Snow Thrower Cab.
Deluxe Snow Thrower Cab Installation
This Deluxe Snow Can fits most 2-stage Cub Cadet snow blowers. So, the below instruction will guide you on how to install the Deluxe Snow Cab into the snow blower.
How to Install Deluxe Snow Thrower Cab
Get your Deluxe Snow Thrower Cab installed by following the steps below:
Step 1 – Prepare the snow blower for maintenance
Place the snow blower on a flat surface area. Then turn off the engine and allow it to cool. Take out the safety ignition key to prevent the engine from turning on accidentally.
Step 2 – Check the components of the deluxe snow cab
Remove the bars, poles and hardware from the snow blower cab box. And make sure you have all the required parts and tools. You can refer to the manual for more detailed instructions.
Step 3 – Assemble the A and B bars
Slide together one set of bars A and B. Install the set screw finger tight. Then repeat this for the opposite side. Make sure you don’t tighten the screws with a wrench until the cab frame has been completely assembled.
Step 4 – Connect the A and B assemblies with bar E
Take the Bar E and insert it into the ends of A and B, with the nut facing inside of the frame. Secure it together with a set screw, finger tight.
Step 5 – Connect bar E and F
Take the poles F and place them into each end of bar E so that the narrow end faces up.
Step 6 – Connect poles G with the A and B assemblies
Place poles G into the ends of A and B assemblies with the narrow end facing up, and secure it finger tight with setscrews.
Step 7 – Connect the D and C rods
Search for the curved rods C and D and place them laying on a flat surface. Then connect D rod to each side of the C rod and tighten them with setscrews. Ensure to match up the arrow points together. Tighten the setscrews with the wrench on the cab kit.
Step 8 – Install the curved rod assembly
Install the curved rod assembly into the top of the G poles you have installed earlier.
Step 9 – Feed the H rods through the sleeves
Make sure you wear safety glasses for the next steps. Get all the flexible rods (you should locate four H rods and one I rod). Open the fabric cab cover to get inside the sleeves. Feed both H rods through the sleeves, then insert the steel ends of the H rods into the top of F poles.
Step 10 – Connect the H rods with the I rod
Insert the leftover H rods over the existing H rods. Then take rod I and insert one end into the other of the ends of H rod. Carefully bend the red over and get it attached to the end of the remaining H rod.
Step 11 – Begin to attach the cab cover
Pull up the cab cover and over the rod assembly. Then slide the rods to the inside pocket of the cover.
ALSO SEE THIS >>> Amazon Credit Card Login – Shop Amazon Credit Card | Amazon.com Official Site
Step 12 – Tighten all the setscrews
Square up the cab assembly, and use the wrench to tighten all the setscrews.
Step 13 – Finish attaching the cab cover
Hold the top of the cover and pull it down and back towards the C and D assembly. Loop the elastic straps to the bottom corners of bar A so as to secure the cover to the frame.
Step 14 – Loosely assemble the clamps
Depending on the unit, the clamp L can either be horizontal or vertical. Clamp K is always horizontal. So, you can loosely assemble clamps M, L and K with the provided nuts, bolts and washers. But ensure not to tighten them at this time. Because the clamp will be slipped on the frame later.
Step 15 – Determine the best location for your cab
With the help of an assistant, hold the cab frame and cover over the snow blower to find the best location for the cab to be secured to the unit. Hold cross bar J to target the best position for the frame.
Step 16 – Mount the clamps
Mount the pre-assembled clamps, M, L and K to the upper handlebars on the snow blower with the provided nuts, bolts and washer.
Step 17 – Attach the crossbar to the clamps
Center both the J crossbar against the two clamps. Hold together with the end clamps using the nuts, bolts and washers. Ensure that the J bar uprights are leveled. The clamps may be required to be mounted to the horizontal handlebar, based on your unit. And then tighten the L and K setscrews.
Step 18 – Insert the cab assembly
Fully attach the front ends of the cab assembly to the ends of the crossbar. Then, put together the upper cab to the J bar upright with two setscrews. Tighten the setscrews to secure it. With the help of an assistant holding the cab horizontally to the ground, tighten all bolts and setscrews.
Step 19 – Fasten the cover to the cab and attach the pouch
Get the cover fastened to the cab and attach the pouch to it.
Step 20 – Open the zippers to allow headlight to shine through (if applicable)
This cab is designed to accommodate snow blowers equipped with headlight. The zippers on the front end of the cab can be opened with the flaps pulled back and secured with hook and loop straps to let the light to shine through.
Step 21 – Make final adjustments
During this time, making adjustments might be necessary for free movement of operational controls.
CHECKOUT >>> Fidelity 401k.com – Fidelity.com Login | Fidelity 401k